You must be at least 18 years old to enter.


Some products on this site contain nicotine. By entering this site, you are confirming that you are at least 18 years of age or 21 years of age where applicable.

Sorry Adults Only

WARNING: This product contains nicotine. Nicotine is an addictive chemical.

 

Aspire Nautilus AIO Starter Pod System

Introduction


The Nautilus AIO Starter Pod System by Aspire incorporates the achievements from Aspire’s pod system such as the Breeze series and the Spryte Kit and the popularity of the Nautilus BVC coil into one crowning creation. The Nautilus Pod System features an e-juice capacity of 4.5mL, an adjustable airflow architecture, and utilizes the beloved Nautilus BVC coil for more flavor and a thicker cloud production. The device also comes integrated with a built-in 1000mAh battery, an output wattage of 12 Watts, and has a one button structure.


Re-fill Method


The Nautilus Starter Pods can simply be removed by squeezing the two side buttons. After which flip the pod upside down, unplug the silicone stopper, fill the pod with your favorite e-juice, and place the silicone stopper back while ensuring the stopper is secured in the correct position. Finally, when you are done, simply turn the pod right-side up again and place it back into the device and once you hear the click then you are good to go.


Coil Description and Installation


The Nautilus System currently uses two variant coils, one designed for regular e-juice and one designed for nicotine salt. The original Nautilus BVC coil is meant for regular e-juice while the newly, created Nautilus BVC coil is meant for nicotine salts with both being rated at 1.8ohm resistance. The replacement method for both coils are the same. Simply remove the Nautilus pod by squeezing the two side buttons then flip the pod upside down. Next, remove the chimney unit, unscrew the previous coil, and screw in the new coil. After which connect the chimney unit back into the pod. Finally, turn the pod right-side up and place it back into the device and once you hear the click then you are good to go.


Charging


To charge the device, just plug in the microUSB cable (included with the package) into the microUSB charging port. The device will flash blue and orange three times when the microUSB cable is connected and when fully charge, the device will flash blue and orange twenty times then remain off. The maximum charge current is capable of reaching up to 1A.


SKU: ASP-KIT-NAU-AIO
Free shipping for orders over $1,000.00

Details

Details

Aspire Nautilus Starter Pod System Specifications:

  • Dimensions: 87.5mm x 37mm x 21mm
  • Maximum E-Juice Capacity: 4.5mL
  • Internal 1000mAh Battery
  • Output Wattage: 12W
  • One Button Architecture
  • Easy Release Pod Design With Snap-In Connection
  • Adjustable Airflow System
  • Protective Drip Tip Top Cap
  • Bottom-Fill System Featuring Silicone Stopper
  • Aspire (BVC) Bottom Vertical Coil Technology - Nautilus
  • 1.8ohm BVC Coil Designed for Regular E-Juice
  • 1.8ohm BVC Coil Designed for Nicotine Salts
  • Bottom Ventilation Hole
  • MicroUSB Charging Port with Max Current of 1A
  • Available in Blue, Green Jade, Silver, Black, Red, Purple

Aspire Nautilus Starter Pod System Includes: 

  • 1x Aspire Nautilus Device
  • 2x 1.8ohm Aspire BVC Coils
  • 2x Additional O-Rings
  • 1x Silicone Stopper
  • 1x MicroUSB Charging Cable
  • 1x Warranty Card
  • 1x Instruction Manual

 

· Do not use or charge with non-approved devices. Overuse of vaping apparatus may cause this product to overheat, malfunction, and/or cause burns or other physical injury.

· Do not leave this product unattended while charging, and do not charge it in your vehicle.

· Do not modify or attempt to disassemble this product. Use accordingly.

· Always turn off your vaping apparatus in between uses.

· Do not attempt to fix, correct, replace, or install any part of the vaping apparatus.

· Electronic cigarettes, personal vaporizers, and e-liquids are not approved by the FDA.

· We DO NOT recommend building/wrapping a coil lower than 0.3Ω in resistance.

· Cease the use of any equipment if there are any slight indications of malfunction.

· Mechanical mods and hybrid connection mods are advanced user items. Please understand all safety procedures before attempting to use.

· WARNING: Some tanks are made from polycarbonate and is not suitable for e-liquid use as some flavors might affect its structural integrity causing it to craze or crack. Please check and see if your tank is made from a suitable material (like glass, Pyrex, stainless steel, etc.) when using citrus, cinnamon, and tea flavors.

Policies

This is Policies tab content

 



You may also be interested in the following product(s)